Patrol Flag Stand

Now that I've made some patrol flags and poles, I need a stand to store all the patrol flags at the troop meeting site. 

Cut List
OSB or plywood 7" x 18" (4)
2x4's ripped to 1.5" x 1.5" x 18" (4)
2x4" (nominal) x 15" cut 45 deg on one end (4)

Other Materials
1/4 x 1.25" x 18g crown staples
3" framing nails
or
1.25" deck screws
3" deck screws

Tools
table saw
miter saw
hammer or framing nailer
pneumatic stapler or cordless screwdriver
  
You can put this together with crown staples and framing nails like I did, or you could screw it together.  It should be pretty straight forward on how to assemble it if you look at the picture.  Make sure that your 3" nails or screws are going into one of the 1.5 x1.5" pieces.


Comments

Post a Comment

Popular posts from this blog

Frapping Mallet

Image
I was doing some research on pioneering for an upcoming Camporee with a pioneering theme.  I came across a blog called Ropes & Poles .  One of the articles was about a tool called a frapping mallet .  It is used to tighten up lashings on larger projects.  You wrap the rope around the handle, brace the head against your spar, and use the handle as a lever to tighten the lashing.  I could not find much else on frapping mallets on the internet.  I don't think these are available for purchase anywhere.  I did find an old sailors tool called a heaving mallet used on rigging in a similar manner. Nevertheless, I was intrigued and had to make one.  This is not your typical project that anybody can make in their kitchen, but if you have the required tools, and know how to weld, it's not that hard. Materials 1/2" x 18" iron pipe 1-1/4" x 6" iron pipe scraps of hardwood spray paint Tools Cut off saw drill press center punch hammer 1...
Read more

Dining Fly Poles

Image
Here is how to make some inexpensive poles for a dining fly.  Make two of these, add an inexpensive poly tarp, some cordage and stakes and you have a very economical dining fly. Materials: 1/2" EMT pipe (10') 5/8" oak dowel 7 or 8" aluminum gutter nail (spike) EMT stands for electrical metallic tubing.  It is used as electrical conduit.  It is galvanized steel, but fairly lightweight.  You can buy a 10' foot length of 1/2" diameter pipe for $2 and change at your local home improvement store. If you want an 8' pole, cut your pipe into two 4' sections.  Cut a 2" piece of the 5/8" dowel.  Hammer into into one end of one pipe.  You may need to sand it a bit to make it fit.  You want a tight fit so it doesn't move later.  Now drill a hole through the dowel that is slightly smaller than the gutter nail diameter.  I used a 7/32" bit.  Hammer the nail in until about 2" is still protruding. Now make a piece to connect th...
Read more

Scout Staff / Stave

Image
This article is about how to make a Scout staff or stave from lumber, as apposed to harvesting a small tree.  Scout staves have fallen out of favor as an item for each scout to carry, but they are still useful as a patrol flag pole or for pioneering projects. I made some from some hickory that came from a tree that died on my property that I had milled.  You could make these from a regular old 2x4.  Pine is not as strong as hickory, but would make a serviceable patrol flag pole, and you could make a bunch of them for about $1.75 each.  For this project you will need a table saw and a router table, as well as a 9/16" roundover bit.  I bought the bit on eBay for $9, and it performed well. First cut your board to 1 1/8" x 1 1/8" on the table saw.  The length is up to you.  The traditional scout stave is 66".  I think 72" is a better length for a patrol flag pole. If you want to have a hole in the end to secure a patrol flag tie, drilling this...
Read more